Click here to print this page.

Griffin & Howe Gunsmithing Scopes and Mounts Guns International #: 101027671 Seller's Inventory #: Category: Gunsmithing - Seller's Information When emailing or calling sellers direct, please mention that you saw their listing on GunsInternational.com Seller: Griffin & Howe Company: Griffin & Howe Member Since: 10/24/08 State: New Jersey Zip: 07821 Country: United States Phone: (973) 398-2670 Platinum Seller Number of Active Listings: 710 Total Number of Listings: 15176 Seller: FFL Dealer Return Policy: 3 day inspection and return policy on used guns. 3 days, Cancellations and Returns may be subject to a re-stocking charge. Payment Types Accepted: Visa, MC, AMEX, Check, Cashiers and Money Order Description: Scopes and Mounts and Pads : Scope Mount Systems The Griffin & Howe scope mount systems have been the proven, quick-detachable systems that return to zero every time. Our Sidemounts and Topmounts have been the choice of serious sport hunters for over 70 years. Our Garand mounts, originally made for sniper scope use under contract to all the U.S. Armed Forces, are still popular with today's shooter. TOPMOUNT custom made and installed only by Griffin & Howe • with 1" rings $1375.00 • with 30mm rings $1475.00 • extra pair 1" rings $450.00 • extra pair 30mm rings $550.00 SIDEMOUNT with STANDARD OR HIGH RINGS supplied with pins and screws uninstalled with 1" rings $775.00 with 30mm rings $825.00 Installation by Griffin & Howe $370.00 + Inletting.  top half with 1" rings *+ $650.00  top half with 30mm rings * $700.00  top bracket without rings * $400.00 base plain $125.00 pair 1" rings - Standard Height $250.00 pair 1" High rings - (3/8" higher) - $250.00 pair of 30mm rings $300.00 GARAND MOUNT with 1 inch TOP EJECTION RINGS base only $125.00 rings only $250.00  top bracket only, without rings $400.00 "Top Half" (bracket & rings only) $650.00 At this time we do not offer 7/8" rings.   *Note: Some adjustment and fitting to existing base will be required. base, bracket and rings complete, uninstalled $400.00 (Supplied with screws and pins) Installation by Griffin & Howe $250.00 Griffin & Howe SIDEMOUNT Installation Instructions Installation should be done only by a competent gunsmith. TOOLS REQUIRED #29 drill (#298) #21 drill #10 drill #0 tapered reamer 9/32" counterbore Remove barrel and action from stock. Mount scope into rings, and assemble sidemount together. Center base to loading port and clamp to action. Adjust to height desired and boresight. Top of base should be parallel to base of action and trued to perpendicular. Adjust scope so that rear on eyepiece is over the tang. Be sure to allow enough vertical clearance for the bolt to operate and clear the eye piece of the scope. Mark the front and rear of the base at the tangent point of the radius on the action. Remove base and mill a radius in it to match the contour of the action. Clamp scope and mount to the action in desired position, aligning for parallelism, perpendicularity, clearance and location as above; then reboresight. In the set clamped position, drill 2 holes for #0 tapered pins with a #298 drill through base and action (see drawing for location) and ream holes with #0 tapered reamer and insert pins. Drill 3 holes with #21 drill through base and action (see drawing). Remove base and tap the 3 holes in action with a 10-32 tap. Enlarge screw holes in base with #10 drill; then counterbore the holes so screw heads will seat flush when assembled. Trim any excess material from the bottom of the base, remove all burrs from base and action. Assemble base to action, fitting 2 pins and tightening 3 screws securely. Grind off any ends of screws and pins that protrude inside or outside of the action. Polish and reblue as necessary Griffin & Howe English style pad, rounded and leather covered $445.00 Griffin & Howe Purdey style pigskin covered pad $610.00 SOLD