 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
M1 Carbine Inland - 100% Correct
Guns International #: 101385941 Seller's Inventory #:
Category: Military Rifles - M1 Carbine - Military Rifles - US
Seller's Information
When emailing or calling sellers direct, please mention that you saw their listing on GunsInternational.com
Seller: Maveriac
Member Since: 3/6/15
Last Name: Kiely
State: Texas
Zip: 75126
Country: United States
Phone: (480) 251-3428
Premium Seller
Number of Active Listings: 4
Total Number of Listings: 56
Seller: Private Seller
Return Policy: 3 day inspection and return policy on used guns.
Purchaser pays actual shipping costs from FFL to FFL.
Payment Types Accepted:
Description:
BEAUTIFUL 100% CORRECT INLAND M1 CARBINE !
PREFACE: The M1 Carbines I sell are not just for shooting, although they can do that too. I have totally disassembled each rifle to check parts authenticity and integrity. I take over 100 photos of each rifle if you want a closer look. When I say 100% CORRECT it means that all the parts are the same as that particular manufacturers production block left the factory with; not necessarily the exact same part, but an identical replacement. A field grade M1 Carbine is neat to have, but if you want a collector grade rifle such as mine, they cost more. Check for yourself what USGI original used replacement parts cost today. A premium stock set can cost $595, Type II Barrel Band $345. NOT CHEAP ! This WWII produced Inland M1 Carbine is just one from an old collection of M1 Carbine and other military rifles. The metal on the barrel, receiver, bolt and all other parts is estimated at 95% plus but does show some slight use wear on contact points, so it has been used to slight degree. The barrel is in excellent condtion with the riflings and lans being very pronounced. The rifle's over all condtion and all of the parts being USGI correct for the serial number, part type identification markings, and production date makes it a true Collector Grade M1 Carbine. The only reproduction parts included are the olive drab sling and kakhi carry case.
Inland Division of General Motors, along with General Motors Saginaw Divisions in Saginaw and Grand Rapids, produced over 3 million M1 Carbines in the M1, M2, T3, and M1A1 configurations in just over three years; arguably the most efficient and reliable manufacturer.
The rifle I am selling has no evidence of being modified by military armorers either during or after WWII based on the fact there are only initial inspection stamps on the barrel and stock. The parts that are supposed to be by manufactures stampings are, and those which are unmarked have been verified as correct base on published photographs from noted M1 Carbine authorities and collectors. Based on the condition of this rifle it must have been stored and cared for properly. It not only looks pristine but is fully functional.
The following is a list of all of the parts to this carbine based on type, stamping, picture verification, or measurement according to Roger Larson's book "Comprehensive Guide M1 Carbine", which is a must have if you are interested at all in M1 Carbines or miltary history for that matter.
- BARREL - Type 2B Late Production, INLAND MFG.DIV. GENERAL MOTORS 11-44 w/P proof mark at 4" from muzzle, short hand guard lip, short barrel skirt, two piece construction;
- BARREL BAND - Type 1A, 3 Weld, Unmarked, Correct;
- SLING SWIVEL - Type 2, Wide, Unmarked, Correct;
- BOLT - Type 3, A.I. on left lug, Round;
- BUTT PLATE - checkered square dot, Unmarked, Correct;
- EJECTOR PLUNGER & SPRING - Type 2, early, Unmarked, Correct;
- EXTRACTOR - Type 2 Modifiied, W.I.;
- FIRING PIN - Type 3, NI;
- FRONT SIGHT - Type 1, R;
- GAS PISTON -Unmarked, Correct;
- GAS PISTON NUT - Type 2, Unmarked, Correct;
- HAMMER - Type 3, H.I.;
- HAMMER PLUNGER SPRING - Type 2, 26 Coil, Correct;
- MAGAZINE CATCH - Type 3, WI;
- OPERATING SLIDE - Type 4, PI in well, 19/32" arm, 7160091 on bottom;
- OP SLIDE SPRING - 10.25" long, Correct;
- SLIDE STOP - Type 2, late, Correct;
- OP SLIDE SPRING GUIDE - Type 2, late flat tip, Correct;
- RECEIVER - Type 2, INLAND MFG. 6764097, narrow tang, spring hole, round mill cut, two dismount notches; REAR SIGHT - Type 1, S on left;
- RECOIL PLATE - Type 3, DI;
- RECOIL PLATE ESCUTCHEON NUT - early short serrations; Correct;
- RECOIL PLATE SCREW - late short thread, Correct;
- SAFETY - Type 3, Unmarked, Correct;
- SEAR - Type 3, R.I.;
- SEAR SPRING - Type 2, tapered ends, Correct;
- STOCK - High Wood Oval Cut, Cross Cannon Cartouche on right, OI in sling well;
- HAND GUARD - Type 3, OI, 2 Rivet;
- TRIGGER - Type 2, R.I.;
- TRIGGER HOUSING - Type 5, INLAND vertical;
- TRIGGER SPRING - late straight ends, Correct;
- OILER - II, Correct;
- CARRY CASE - kakhi reproduction;
- SLING - olive drab reproduction;
- MAGAZINES - Type 1, IS, flat base;
- MAGAZINE BUTT STOCK POUCH - Original, olive drab
Sales transaction must comply with all state and federal firearms sales and shipping regulations. Buyer pays $35 shipping and insurance cost for transfer to a currently valid FFL of your choice within the contiguous 48 United States. Although fully functional, this rifle is being sold as is with no expressed or implied warranties. No Trades Considered ! Accepted method of payment is USPS Money Order ONLY !
SOLD
Curio/Relic: Yes
Manufacturer: Inland Mfg.
Model: M1 Carbine
Serial Number: 6764097
Caliber Info: .30 Carbine
Bore: Rifled
Ejectors: Excellent
Condition: Excellent
Metal Condition: Excellent
Wood Condition: Excellent
Bore Condition: Excellent
Action: Semi- Automatic
Weight: 6lbs
Sights: Fixed Front - Dual Aperture Rear windage adjustable
Manufacture Date: 11-44
Extras: Two Original Magazines, Mag Pouch, and Sling
Case: Zippered Canvass
Item Location: Texas