The server has not detected any activity for the last 3 hours.
For your security, your session will expire in 2 minutes and you will be redirected to the Sign In page.
Would you like to stay signed in?
This is an M1 Garand Op Rod marked "7790722-SA" It is NOT marked "NM" but should be proper for your post war National Match rifle. Rods are parkerized and used. We have a number of
...Click for more info
A surplus U.S. M1 carbine Quality Hardware original reciever with not much finish left but not pitted ie damaged I can see. These reciever on the loose are not easy to find,SN evident and clear: 16216
...Click for more info
This is an original USGI M1 Garand rear hand guard clip that is milled, arched and grooved.
It has the typical milling marks of a W.R.A. (Winchester) production. A great original part for you early W
...Click for more info
CLINOMETER MACHINE GUN M 1917 AND ALSO MARKED HIGH BRIDGE N.J. AND ALSO MARKED 1943 SEE PICTURES. WANT TO PURCHASE CALL SHOP 716-941-3946
...Click for more info
This is a WWII Underwood US 30 Cal M1 Carbine Flat Bolt. This example is in very good condition with some signs of wear on high spots. Clearly marked -U-. Has a light film of grease or preservative. T
...Click for more info
HOLLIFIELD ARMY & NAVY PRACTICE ROD CO. MIDDLETOWN N.Y. MADE FOR A SPRINGFIELD 1903 MILITARY RIFLE . MADE IN THE EARLY 1900,s .A GREAT COLLECTIBLE PIECE FOR ANY MILITARY OR 1903 COLLECTOR.FO
...Click for more info
"Dotter Apparatus " Hollyfield Target practice rod company, Middletown, New York USA. For use with the service automatic pistol 1911. Very rare item seldom seen. A great addition to anybody'
...Click for more info
SOLD This is an early "I" stock M1 Carbine in complete ready to install condition. It has the early W.R.A G.H.D. in a box with the large ordnance wheel. The top hand guard is th
...Click for more info
This is a, what appear to be NOS, USGI M1917 Extractor manufactured by Eddystone. They are all well marked with the "E". These original 1917 parts are getting scare and there are NONE being
...Click for more info
This is a, what appear to be NOS, USGI M1917 Ejectors W/Sprngs manufactured by Eddystone. They are all well marked with the "E". These original 1917 parts are getting scare and there are NON
...Click for more info
This is an Inland type VI (M2) slide marked PI. It is in excellent condition and comes complete with slide stop. Payment by check or USPSMO.
Thanks. Ronny
...Click for more info
This sight is Remington-Marked. The condition is Very Good, showing typical wear and finish loss from normal use and age. Comes with the rear sight Axis screw and nut.;
...Click for more info
4 unissued still in the box, Remington Bolt Assembly M/1903-A3, drawing No. B 146891. The box is in excellent condition with two heavy paper packs, containing 2 bolt assemblies. The assemblies are new
...Click for more info
Very good to excellent condition SA-3 Hammer. This is correct for Springfield Armory Garands built from Jun 42 to Jun 43 but will fit all others.
Ready to install. May not be the same color finish as
...Click for more info
Very good to excellent condition SA-2 Hammer marked C46008-2 SA. This is correct for Springfield Armory Garands built from Sept 1940 to Jun 1942 or serial numbers 65001 thru 680000 but will fit all ot
...Click for more info
This an IBM type 3 round bolt. Bolt is stamped AOB. Both Firing pin and extractor are stamped WB. Ejector is type 1. IBM only used type 1 ejectors throughout production. Photos clearly show stam
...Click for more info
This is amilled Tpe 2 sight Marked "HI" for Inland Division.Sight is is in excellent condition. No dings or scratches, Parkerizing is excellent. See Photos.
...Click for more info
These recoil plates were used as replacement parts. Manufactured by Prescion Instruments Company also known as Wadco. These can be found on any manufacturers Rifles. Was used in WW2 late 1943 to end o
...Click for more info
This recoil Plate is in excellent to NOS. This type 2 was used by inland for early manufacturing runs Parkerization is excellent and no sign that it was ever installed. Used in serial# range 100
...Click for more info
This operating slide is for serial # range 1,982,520-2,352,519. Rifle produced April 1943-May 1944. Last serial number block of Standard products production. Excellent to New condition shows no signs
...Click for more info
This is a NOS Remington Arms Model 1903A3 Barrel dated 1943 in the original wrapper with original box it was shipped from the factory in December of 1964 from the Dept. of Army Rock Island Arsenal. Th
...Click for more info
This is an M1 Garand Op Rod marked "6535382" It is NOT marked "NM" but should be proper for your post war rifle circa 1952 to EOP. Rods are parkerized and used. We have a number of
...Click for more info
Hard to find..RARE...Serviceable Gun Charger for the a range of 20mm Cannons..like the M24 among others
Price includes..Shipping Charge to you!
Phone 403-472-3320
...Click for more info
Brand new Boyds complete Birch stock set, with new furnature ! Small amount of inletting required around the action to permit an accurate fit !
No sales out side the USA!
Shipped FedEx Gro
...Click for more info
SEE THE PICTURES OF M-16/AR15 RIFLE MAGAZINE LOADER & UNLOADER & SIGHT BRACKET FOR SCOPE MOUNT:
1. MAGAZINE LOADER & UNLOADER PRICE $35 WITH SHIPPING
2. SIGHT BRACKET FOR SCOPE MOUN
...Click for more info
I have a NM National Match Colt slide for sale. This is the slide that Colt used from 1963-1968 on their 1911 National Match Pistols. The NM7791534 and the Colt address is marked very clearly an
...Click for more info
USGI Military Issue M1 Garand Sling ORIGINAL OD Canvas 1950s & 60s,
These are in very good condition, all original hardware and sling,
Check pictures, NO CC FEES, Call to pay with yo
...Click for more info
An original issued M60 Barrel Bag brought home from Vietnam by a GI - not a later produced item this bag was actually used by a soldier who was issued an M60 during the Vietnam War.
...Click for more info
M1 CARBINE BOLT ROUND
NO MARKINGS
MANUFACTURE UNKNOWN
TWO USED RECOIL SPRINGS
EXTRACTOR SPRING
EJECTOR AND EJECTOR SPRING
M1 BOLT ASSEMBLE TOOL
SOLD AS IS
PAYMENT ACCEPTED
U
...Click for more info
This is a WWII USGI M1 Carbine slide, type II with the narrow arm joint.
The part is marked "J" which may indicate either a wartime production by Saginaw or a post-war rework.
The slide sh
...Click for more info